For semi-integrated models, reuse the existing holes. Carefully uncoil the copper tubing and loosely thread it from the dishwasher bay through the cabinet side and up into the cabinet via one of the floor holes. Uncoil enough copper to get past the front of the bay. Using a tubing cutter, cut the line. Insert a narrow tube-bending spring inside the end of the copper nearest the hot-water valve.
- gentry dating.
- distance dating advice.
- Msrp is that was easy to Check the microwave frequency range..
- how much does radiocarbon dating cost.
Use the spring to shape the tubing toward the valve then down to the hole in the cabinet. Be careful not to kink it. Slide a compression nut, then a ferrule over the end of the tubing at the valve. Hand-tighten the nut over the ferrule and onto the valve. Using an adjustable wrench, tighten it another quarter turn. Tube-bending springs can fit either inside or outside a pipe. The inside springs can only be used on a pipe's ends, but they make tighter turns. Use outside springs to gently curve the middle of a pipe.
Find the two front-to-back clear paths on the underside of the dishwasher—these are meant to keep the copper tubing and electrical wiring away from the motor as they run from the back of the dishwasher bay to the front of the appliance. Measure the distance from these paths to the sides of the dishwasher.
Transfer the measurements to the floor inside the bay. Note which side leads to the water hookup and which side is for the wiring.
- Connect the Water Supply Hose.
- free wordpress themes for dating site.
- best late night hookup app.
- Your browser security needs to be updated?
Using an outside bending spring, shape the copper pipe so it wraps down the cabinet side and along the mark for the water-pipe channel. Twist the electrical wire so that it lies in the correct path as well. Use tape to secure both to the floor in position over their marked lines.
Lay down a tarp to protect the floor and tip the dishwasher on its back. Remove the cover panel at the bottom of the unit. Wrap Teflon around the water inlet's threads. Screw a brass elbow onto the inlet. Tighten it with an adjustable wrench. Stand the dishwasher up and push it up to the bay.
Check that the water and electrical lines are properly aligned. Feed the end of the drain line from the dishwasher through the side of the cabinet and up via the unused floor hole. Then have a helper guide the drain line as you slowly slide the dishwasher in place. Using the inside bending spring, turn the copper supply to the elbow.
Use the Short Hose as an Extension
Cut off any excess pipe but leave 2 inches of straight copper for the compression fitting. Slide a compression nut and ferrule over the end of the pipe and hand-tighten the nut onto the inlet. Slide a cable clamp over the end of the exposed wires until it's around the plastic or metal sheathing bundling the wires together. Using a screwdriver, tighten down the clamping bracket over the sheathing to hold the wires in place.
Unscrew the star-shaped nut on the clamp, then push the wires and threaded end of the clamp through the hole in the side of the unit's junction box. Hand-tighten the nut back on the clamp from the inside of the box.
Tighten the nut with pliers or a screwdriver. Line up like colors of wire together—white to white and black to black—and tighten them together with wire nuts. If you have Romex plastic-sheathed cable, connect the green ground wire to the dishwasher's green or bare-copper wire with a wire nut.
If you're using BX cable, the armored jacket works as a ground when it's clamped to the junction box. Wrap the exposed tip of the dishwasher's ground wire around a mounting screw on the junction box and clamp it down with the screw. Stuff the wires into the box and cover it with the metal cover plate.
Whirlpool water hookup
Screw the plate to the box. Slip a hose clamp over the end of the dishwasher's drain line, and push the hose over the sink drain inlet—either branching off the drain tailpiece or the side of the garbage disposer. Take care not to kink the line or wrap it around the spray hose line. Slide the hose clamp over the connection and turn the screw to tighten it down.
Install the Water Supply Hose on Your Steam Dryer
Wrap a loop of plumber's strapping around the drain line with enough excess to match up a pair of holes. Hold the hose and strapping against the back of the cabinet so it makes an arc that's higher than the drain inlet. Using a screwdriver, attach the strapping to the cabinet wall. Reach down and adjust the feet on the front of the dishwasher until the mounting brackets touch the underside of the counter. Open the dishwasher door. Do not install the icemaker tubing in areas where. When using any electrical device such as a power.
All installations must be in accordance with local plumbing. Follow next instructions carefully. Replace the filter if necessary. To determine how much tubing you need: Then add 8 feet. Be sure there is sufficient extra tubing about 8. Be sure that the kit you select allows at least 8 feet. Saddle-type shutoff valves are.
What Size Is a Refrigerator Water Line? | Home Guides | SF Gate
Install the shutoff valve on the nearest frequently. Turn on the nearest faucet to relieve the pressure on. Table of Contents Add to my manuals Add. Kenmore - Elite