If you have a room with only one phone jack but you want two-line access in that room, there's a simple remedy.
Head to your local hardware store and pick up a dual phone jack plate. It has two jacks on it, one on top of another. Simply hook the red and green to the top jack and the yellow and black to the bottom jack, and you now have two-line access in the same room without having to run additional wires. Continue to Part 2: Installing a New Phone Jack. First, let's look a few scenarios where someone may need a second line in their home: A home office may require a dedicated line for business purposes. You may have children who need their own line so that they stop tying up the main phone line.
Many people like having a dedicated number for faxes. Dial-up ISP users may want a dedicated line for their online surfing.
Buy me a beer!
Step 1 - Activate the New Phone Line The first step to adding a second line is calling your phone company. Step 2 — Unscrew the Faceplate If you have a certain room, like a child's room or an office, where you want the second line, the switchover can be simple. Step 4 — Check for a Dial Tone Don't screw the plate back on yet.
Step 5 — Re-install the Faceplate Wrap the red and green wires back down the phone cable and tape the ends with black electrical tape. Step 6 — Final Touches Don't get too excited!
- Phone Jack Wiring Diagram.
- How to Wire a Telephone: 12 Steps - wikiHow.
- Ready to do your own home telephone wiring?.
- free online dating websites over 40!
- .
Your local phone company will come and do your wiring for you, but it will cost you. Wiring a jack is not difficult and it is totally fine to add a new jack or internet phone jack to your system. You should disconnect the main phone line from the source before continuing wiring a phone jack. The phone line usually comes in by your electrical panel. There will be a small box with a phone line going in and coming out.
This is called your "Connecting Block". Carefully remove the cover and disconnect the wires noting where you removed them from. You can take a digital picture of the box so you can refer back to it when you want to re-connect! When wiring a phone jack, you will notice that the wires are different colors. Here is a chart that defines the colors:. These instructions assume that you have already run the home telephone wiring to the new location. All you need to get started is a screwdriver, a pair of needle nose pliers and a wire stripper.
Who wrote this page?
Make a small "hook" in the wire with the needle nose pliers and place the wire under the screw. Make sure the wire is wrapped around the screw in a clockwise direction so it will stay under the screw when you tighten it. Attach your landline's receiver to your router if necessary. Some landline phones e. You'll use an Ethernet cable to connect the "Internet" port on your receiver to any free port on the back of your router. Plug your receiver into a power outlet. Using the power cable which came with your landline's receiver, plug one end of the cable into an electrical outlet and then plug the other end into the "Power" port on the back of the receiver.
Your phone receiver may have a built-in power cable. If so, just plug the free end of the cable into an electrical outlet.
DIY Home Telephone Wiring
If your phone is properly wired and your phone company has activated service for your landline, you should hear a dial tone when you pick up the phone. At this point, you're free to make a call or set up your landline phone based on its manual. How do I hook up my new phone line to the phone company's box outside?
If the box in question only has two possible connections, just plug a RJ11 jack into the one marked Line 1. If there are more, you would be well advised to ask your phone company to send out a technician. Not Helpful 2 Helpful The cable has 4 wires. However, only 2 are used. Which ones do I connect?
- free dating sites in oshkosh wi!
- How to Hook Up a Second Phone Line | pcppk.com.
- The Basics of Telephone Wiring.
- .
- .
As long as you use the same colors on both ends, it doesn't matter. Not Helpful 3 Helpful 4. You could use a multimeter. Touch one of the wires of the multimeter to the phone wire, then touch the other one to another port on the phone, or even to another part of the wire, at about 10 cms apart.
Not Helpful 14 Helpful 8. Not Helpful 9 Helpful 5. How do I connect blue and white wires to red, green, yellow, and black wires? With a soldering iron and some solder would be the most reliable option.
Doing your own telephone wiring
Or turn off the electricity and wrap the metal of the wires around each other -- this option will be easy but may be slightly unsafe and won't last if it gets knocked. Not Helpful 7 Helpful 2. Make sure the wiring is not loose, and try the phone in a different jack. If that is not the case, try plugging in a different phone. If that fixes the problem, you will need to get a new phone. If that is not the issue still, contact your telephone service provider.
Not Helpful 2 Helpful 0.